 一、配置交换机
% Y) i4 W. k' y% d Switch>en ----进入特权模式% o) e2 W/ i& g) ~+ c" z3 @
Switch#config t ----进入全局配置模式
( _, Y( A8 z' _ Enter configuration commands, one per line. End with CNTL/Z.& A0 r: Q/ [/ a2 g& |; C
Switch（config）#vlan 10 ----配置第一个vlan1 u2 F: M' P1 P5 l! ~
Switch（config-vlan）#name 10 ----给vlan命名
2 c0 j0 K8 U+ w* Q( u- P Switch（config-vlan）#exit! g- j3 x5 h- X
Switch（config）#vlan 20 ----配置第一个vlan
7 [6 W A6 h% j* Y4 U, a Switch（config-vlan）#name 20 ----给vlan命名* ?5 c, q5 O+ _$ _6 J
Switch（config-vlan）#exit& p9 j& s; {& M
Switch（config）#int f0/1 ----进入f0/1端口
- G7 t$ ?, o! b4 a8 T6 o9 y Switch（config-if）#switchport access vlan 10 ----把端口分配给vlan10; p/ T& c+ c) o( R( U
Switch（config-if）#exit; \1 C- z6 u K6 Y
Switch（config）#int f0/11
0 v$ I- `0 B# @$ |" z Switch（config-if）#switchport access vlan 201 c2 b. L+ i, c' Y* d4 }
Switch（config-if）#exit$ p: r4 R! R: X/ ]1 \$ @# w, W
Switch（config）#int f0/24
8 p( }6 }- m8 ?" Q3 n! D4 ` I Switch（config-if）#switchport mode trunk --配置f0/24为TRUNK模式( s# R+ X% \: r5 b1 {6 v
Switch（config-if）#exit$ c; h; @* Q& t, B. p" ^* I
二、 配置路由器! A- V1 J/ V; i
Router>en
! Q8 t7 |" o% h8 ~" L Router#config t0 K$ p7 a* r& U1 I7 G
Enter configuration commands, one per line. End with CNTL/Z.5 `. \; m/ ]# h2 c
Router（config）#int f0/0 ----进入f0/0端口/ B* l! F# v& D0 ^! X. U* P
Router（config-if）#no ip add ----不配置IP地址, m( c q2 @1 V1 J4 ?
Router（config-if）#no shutdown ----开启端口" V! V" l, L1 V T: l
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up" J- C: r& c" a0 {$ W) O" @
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up6 k8 P( _0 A, r1 Z7 D, B2 [& t
Router（config-if）#exit' Z6 p. f5 S+ j5 g+ c
Router（config）#int f0/0.1 ----配置子接口* n0 C$ ?% H: d) ?9 W
%LINK-5-CHANGED: Interface FastEthernet0/0.1, changed state to up5 A4 J _- s; s5 T
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.1, changed state to up- z# n# P+ [! \
Router（config-subif）#encapsulation dot1Q 10 ----配置dot1Q协议9 C8 `( L8 }5 Y; J% N
Router（config-subif）#ip address 192.168.1.254 255.255.255.0
( e: W6 J8 Q/ b; ^2 H# f: h Router（config-subif）#no shutdown
# \. x. s- z, I. j, S" ?9 \. P6 r Router（config-subif）#exit6 c* w2 a' V$ E: A
Router（config）#int f0/0.2
" @, f5 P5 @7 x. [6 q; i %LINK-5-CHANGED: Interface FastEthernet0/0.2, changed state to up( j; a0 [9 ?# Z; I5 G* @' D" Y
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.2, changed state to up9 C- v2 s" d- ^; H- _
Router（config-subif）#encapsulation dot1Q 20* b" d+ K, J k" q. B" J* n4 O3 V* ^: b
Router（config-subif）#ip add 192.168.2.254 255.255.255.0
% F3 x1 B' v- R4 O+ G Router（config-subif）#no shutdown" ^9 }* Q, L& T ~, C/ s
Router（config-subif）#exit$ [9 [- U2 k$ z- T
Router（config）#
g* }) {0 @, f3 p 三、 验证
) X a1 Z6 a( H! D% c" f; h P1的IP地址/ q# R8 ]7 T* u. V% y* j- @
P2的IP地址$ a6 k2 \7 e ^2 C l1 }
P1能够ping通P2，P2能够ping通P1则配置成功。9 Z6 h' r& t3 V1 w
 4 o$ g- I: d4 t8 _! B+ S
 |
发表于 2012-8-3 20:28:11
