137.20.0.0/24 is subnetted, 1 subnets c 137.20.20.0 is directly connected, ethernet 0
# z! Z, [6 x( ?, ] 172.168.0.0/16 is variably subnetted, 7 subnets, 2 masks: i; k& O2 [6 M% w7 d% E
o ia 172.168.30.0/24 [110/65] via 172.168.100.3, 00:09:03, serial 1.1
" _/ \- T: X- y# `3 c. ^ i 172.168.40.0/24 [100/8576] via 172.168.200.2, 00:01:11, serial 1.2
& Y3 X7 e2 j* i" O( g/ R# q& F o ia 172.168.60.0/24 [110/1572] via 172.168.65.1. 00:09:03, bri0
' M2 Y6 i$ l* U+ U* j c 172.168.65.0/24 is directly connected, bri0+ I$ E: M7 N4 ]% |% ^ X: T( r: o
c 172.168.100.0/24 is directly connected, serial 1.1
, T0 r' C+ q8 m3 {) M o 172.168.100.0/24 [110/64] via 172.168.100.3, 00:09:13, serial 1.1
# D+ p/ F9 O% v! c2 t' R7 H2 ~ c 172.168.200.0/24 is directly connected, serial 1.2
9 u q! V$ y8 @1 R o e1 192.168. 21.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0
8 _& Y2 Z) C/ Q: R% x. g o e1 192.168. 17.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 01 r) C4 h8 q2 k. X- {1 M* w
o e1 192.168. 70.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0
4 k2 ?1 j5 Y" {3 D5 | o*e1 0.0.0.0/0 [110/21] via 137.20.20.1. 00:09:03, ethernet 0
; V1 J# y# ^$ S r5#show ip ospf int bri0& y. l/ S8 f/ x8 i ?8 Y! k
bri0 is up, line protocol is up (spoofing)
' X1 e! S* t) c internet address 172.168.65.2/24, area 10
6 f) C* }" x b3 G+ u& s process id 1, router id 172.168.200.1, network type point_to_point, cost 1562' L! [: [( f( O
run as demand circuit
& s; U" z6 h9 i0 } donotage lsa allowed.( O; A# P8 c# J: t" `; z7 J7 B) j; T( K5 R
transmit delay is 1 sec, state point_to_point,& A/ m/ e* K! P" E# N0 H! F
timer intervals configured, hello 10, dead 40, wait 40, retransmit 57 c. q9 W3 L6 ]$ F+ t; f! }1 O! P
hello due in 00:00:06
0 T- R% D+ |4 I) K% _( O neighbor count is 1, adjacent neighbor count is 1
, e/ B# O4 }* G$ ^1 B$ r adjacent with neighbor 172.168.100.6 (hello suppressed)9 Q5 \" K5 x& x8 T7 M/ z9 G
suppress hello for 1 neighbor(s)
2 }5 W7 {8 Q. A# K r5#show dialer
/ C1 O, R$ d: q/ T# {0 |3 e0 X$ n4 P
3 X' C" J# D8 b! } P: E5 m
bri0 – dialer type =isdn
3 ^8 @$ H9 G: D. X; A$ Y( C$ C dial string successes failures last called last status5 A' m+ v7 A1 H* U1 R. N, X: H
4930622 1 0 00:08:45 successful; u% X3 V: }. I/ C
0 incoming call(s) have been screened
4 r) {5 m x' [( h) I' K; U 0 incoming call(s) rejected for callback
- x/ G8 V( h0 |' K9 |! w" w bri0:1 – dialer type =isdn% Z1 g% V$ y4 b! D1 Y; w4 Q
idle time(45 secs), fast idle timer (20 secs)
( q5 G1 @# r3 u wait for carrier (30 secs), re-enable (15 secs)7 F5 f! c; v# l8 y8 D" Y. F. [
dialer state is idle" E# b( Q- o# X0 m
bri0:2 – dialer type =isdn3 ^( z. b% }& \7 }
idle time(45 secs), fast idle timer (20 secs)6 A i. ^; k$ c( L' w
wait for carrier (30 secs), re-enable (15 secs)% h7 ?6 N2 _' h! i1 T
dialer state is idle n1 H. `$ y0 ^. U8 s: I3 N
r5#
/ Q& f5 [* }) n* n0 l now go back to router r7 and bring up router r7’s interface s4 again
& T: x2 q; n. E: S- K, G 3. ipx configuration –15 pts (1 hour), ^ m0 t1 R/ X- [( ?/ _* P; }
a. configure all the active interfaces, including loopbacks, on routers r1, r2, r3, r5, r6, and r8 for ipx.- z$ D7 Y" ?2 N" M
b. configure router r8 and the lan interfaces on routers r3, r4, r5 and r6 for ipx rip.
+ D2 p/ H! Z/ t c. configure router r1 & r2 for ipx nlsp.& l! ?. H8 @* g! |9 |# o) @' ^- t
d. configure the serial interfaces on the rest of the routers for ipx eigrp( not routers r1& r2 these oly use nlsp), also make the ethernet interface on router r2 ipx eigrp only.
% E; Y% P8 M# i( s% _8 C% S. U e. configure the bri0 interfaces on routers r5 & r6 as ipx rip.5 O5 m6 G* n) T/ x0 J! q- P6 A* c( ?
f. after this point you should be able to see all the ipx networks in all the routers routing table. test connectivity with ipx ping. |
发表于 2012-8-3 20:12:39
