思科认证考试试题：CCIE实验考试_BootCamp3.0(10)

会计考友

　　137.20.0.0/24 is subnetted, 1 subnets 　　c 137.20.20.0 is directly connected, ethernet 0
, q. \" C$ \* E! H　　172.168.0.0/16 is variably subnetted, 7 subnets, 2 masks
4 p0 F% h( W  N+ U0 u　　o ia 172.168.30.0/24 [110/65] via 172.168.100.3, 00:09:03, serial 1.1
　　i 172.168.40.0/24 [100/8576] via 172.168.200.2, 00:01:11, serial 1.2
　　o ia 172.168.60.0/24 [110/1572] via 172.168.65.1. 00:09:03, bri0
9 H; v4 k) [+ O5 T6 }# U- D: b　　c 172.168.65.0/24 is directly connected, bri0
1 z+ G, \* l8 U, L5 H　　c 172.168.100.0/24 is directly connected, serial 1.1
# S$ ^& j2 L0 I/ V　　o 172.168.100.0/24 [110/64] via 172.168.100.3, 00:09:13, serial 1.1
6 T/ \" F/ Y! F　　c 172.168.200.0/24 is directly connected, serial 1.2
% ?0 k5 ^* F* A  b- N* D　　o e1 192.168. 21.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0
' }5 g) H% z$ u/ U+ q' Y　　o e1 192.168. 17.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0
　　o e1 192.168. 70.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0
$ h% ^' U! F1 k2 Z. U$ L7 D　　o*e1 0.0.0.0/0 [110/21] via 137.20.20.1. 00:09:03, ethernet 0
; q" c& j" d( u# @. k6 X　　r5#show ip ospf int bri0
　　bri0 is up, line protocol is up (spoofing)
　　internet address 172.168.65.2/24, area 10
　　process id 1, router id 172.168.200.1, network type point_to_point, cost 1562
　　run as demand circuit
  i0 o) s3 V! f% g　　donotage lsa allowed.
　　transmit delay is 1 sec, state point_to_point,
) ^  a8 r2 s! N$ m8 m2 u9 o- A( t3 |　　timer intervals configured, hello 10, dead 40, wait 40, retransmit 5
　　hello due in 00:00:06
　　neighbor count is 1, adjacent neighbor count is 1
　　adjacent with neighbor 172.168.100.6 (hello suppressed)
　　suppress hello for 1 neighbor(s)
1 b7 \; k2 m! P. U) x　　r5#show dialer
9 \  |; M$ g- ^: q+ L1 e0 D' D

　　bri0 – dialer type =isdn
　　dial string successes failures last called last status
　　4930622 1 0 00:08:45 successful
4 A4 ?$ S( ~  C  P5 h' x　　0 incoming call(s) have been screened
　　0 incoming call(s) rejected for callback
　　bri0:1 – dialer type =isdn
　　idle time(45 secs), fast idle timer (20 secs)
+ k& H- j4 e* n% R6 {* L$ t8 R  w　　wait for carrier (30 secs), re-enable (15 secs)
　　dialer state is idle
/ j3 S: S, g$ p　　bri0:2 – dialer type =isdn
　　idle time(45 secs), fast idle timer (20 secs)
0 q( B  B. k/ ~* I　　wait for carrier (30 secs), re-enable (15 secs)
, o2 q) e2 G* k- ~9 f0 E1 R- m+ m( s　　dialer state is idle
; F; O, Y* Z+ Y　　r5#
　　now go back to router r7 and bring up router r7’s interface s4 again
　　3. ipx configuration –15 pts (1 hour)
' @  a1 E2 F4 g# ]* P　　a. configure all the active interfaces, including loopbacks, on routers r1, r2, r3, r5, r6, and r8 for ipx.
6 E# n7 S3 q  _" T8 M　　b. configure router r8 and the lan interfaces on routers r3, r4, r5 and r6 for ipx rip.
　　c. configure router r1 & r2 for ipx nlsp.
　　d. configure the serial interfaces on the rest of the routers for ipx eigrp( not routers r1& r2 these oly use nlsp), also make the ethernet interface on router r2 ipx eigrp only.
　　e. configure the bri0 interfaces on routers r5 & r6 as ipx rip.
4 s9 z6 Y) J- d4 B$ A) d　　f. after this point you should be able to see all the ipx networks in all the routers routing table. test connectivity with ipx ping.